The Dc Motor Speed Control Methods Engineering Essay

Table of contents

Abstraction

This paper describes the Matlab and simulink converts into actuality of the DC motor velocity control methods, viz. field opposition, armature opposition control methods and armature electromotive force, and feedback control system for DC motor thrusts and this paper describes mathematical modeling, simulation of DC motor system utilizing computing machine simulations Matlab and simulink, by this system response to alter assorted parametric quantities like system stableness, perturbations, analysis and optimisation of theoretical account parametric quantities with regard to the quality of control. If simulation techniques are used for finding the control parameters a simulation theoretical account is necessary, which has to be constructed from the analytical theoretical account.

Introduction

DC Motor is an electrical motor and it most normally used in an electrical device for easy to drive the instruments, steel turn overing Millss, electric Cranes, and robotic operators due to precise, broad, simple, and uninterrupted control features. To command the velocity of low power DC Motor rheostatic armature control method were used. The basic parts of the DC motor are- axle, rotor ( armature ) , stator, commutator, field magnet, and coppices. In the geometry of coppices, commutator contacts, and rotor twists are arranged in such a mode so that when power is applied so mutual oppositions of the energized twist and the stator magnets are misaligned and the rotor will get down to revolve until it is about aligned with the stator ‘s field magnets. When the rotor reaches to alignment, the coppices move to following commutator contacts, and stimulate the following twist.

There are variable types of DC Motor available in market with the good and bad qualities. Bad quality means slowdown in efficiency. To retrieve or halt this sort efficiency job accountant is introduce in the system.

Brushed DC motors are most widely used in applications and its ranging from plaything to push-button adjustable auto seats. Brushed DC ( BDC ) motors are cheap but easy to drive.

Brushed DC motors are easy available in all size and form with the broad scope from large-scale industrial theoretical accounts to little motors for light applications ( such as 12 V DC motors ) .

BDC motors are most normally used in easy to drive, with variable velocity and high start-up torsion applications.

The circuit which was given is drawn in the Matlab by utilizing simulink. In the circuit diagram the flow of current

Brushed DC Motor basics

A Brushed DC Motor consists of stationary fixed lasting magnets i.e. stator, a revolving electromagnetic i.e. rotor and flux, which is concentrated by metal. Rotor rotate by the attractive force of the opposite poles and repulsive force of the similar poles, it cause to bring forth torsion and torque Acts of the Apostles on rotor and so do it turn. As the rotor start to revolve or turn so fixed coppices make and interrupt the contact in such a manner that with the revolving sections ( commuting ) . The rotor spiral of the brushed motor energized and de-energized in such a manner so that the rotor start to bends. By reassigning the power to the motor, current generate in rotor spirals and therefore the North and south poles are reversed and because of the motor change the way. From the Strength of the magnetic field, velocity and torsion of the motor depend

Construction and operation of the Brushed DC Motor is shown below in figure  .for the building of the BDC motor ever the same constituents are required i.e. Stator, rotor, commutator and coppice.

The rotor surrounded by the stationary magnetic field which is generated by the stator and this filed is generated by the lasting magnet or electromagnetic twist. On the building of the stator, different types of BDC distinguish.

Rotor is besides known as an armature and it is made up of one or more twists. Magnetic field is produce when they energized. When the opposite pole of the magnetic poles, pull to each other which is generated by the stator, and doing the rotor to turns. The opposite poles are ever pulling to each other. As the motor turns, the twists are being invariably energized. This divergence of the field in the rotor is called as an armature.

Brushes and commutator

There is no demand of accountant in BDC to exchange current in motor twist. The commuting twist of the BDC motor is done automatically. Reside on the axel of rotor there is a metameric Cu arms called commutator. Carbon brushes slides over the commutator coming in a contact with the different sections of the commutator as the motor starts to turn. When the electromotive force is applied across the coppices of the motor so dynamic magnetic field is generated inside the motor. Brushes and commutator are the most of import parts of the BDC motor that are most prone to have on because they are the skiding portion to each other.

Speed Control

The Speed of a DC Motor is straight relative to the electromotive force. By utilizing the digital accountant electromotive force can be control and to bring forth the mean electromotive force pulse-width modulated ( PWM ) signal is used. In motor there is a motor weaving which acts as a low base on balls filter so PWM develop a suited current in the motor twist.

Advantage:

  • Cheap in monetary value because low cost of building.
  • Widen a life by replacing a coppice.
  • Cheap motor and simple control.
  • Speed/Torque is normal at high velocity.
  • On fixed velocity no control is required, Controller is required merely at variable velocity in this status same accountant can be used.

Disadvantage:

  • Care is required for brushed DC Motor because of coppice.
  • If the coppice clash additions, cut down the utile torsion.
  • Heat dissipation is hapless because of internal rotor building.
  • Speed scope is limited because of the mechanical restriction on coppices.
  • Life is besides shorter.
  • Noise is generated due to brush.

Application illustrations: traveling playthings, fans, pressmans, automatons, electric motorcycles, doors, windows, sun roofs, seats, sociables, nutrient processors, can openers, liquidizers, vacuity cleaners, toothbrushes, razors, java bombers, etc.

Physical Parameters

Moment of inactiveness of the motor ( J ) = 9.89 E-7 kilogram Nm s/rad

Muffling ratio of the mechanical system ( B ) = 5.84E-7 Nm s/rad

Electromotive force or motor changeless ( K=Ke=Kt ) = 0.008 Nm/-w

Electric opposition ( R ) = 0.80 ohms

Electric induction ( L ) = 0.00041H

Friction coefficient, degree Fahrenheit

Input ( V ) : Beginning Voltage

Output ( theta ) : place of shaft

the rotor and shaft are assumed to be stiff

Decision

Brushed DC motors are really simple to utilize and easy to command,which makes them a short design-in point. PIC microcontrollers, particularly those with CCP or ECCP faculties are ideally suited for driving BDC motors.

Reference

  1. hypertext transfer protocol: //www.wiringdiagrams21.com/2009/09/26/circuit-diagram-for-dc-motor-control-by-a-collins
  2. hypertext transfer protocol: //www.nxp.com/documents/application_note/AN10513.pdf
  3. hypertext transfer protocol: //ww1.microchip.com/downloads/en/AppNotes/00905a.pdf
  4. hypertext transfer protocol: //www.orientalmotor.com/MotionControl101/AC-brushless-brushed-motors.html
  5. hypertext transfer protocol: //ww1.microchip.com/downloads/en/AppNotes/00885a.pdf
  6. hypertext transfer protocol: //www.dynetic.com/brushless % 20vs % 20brushed.htm
  7. file: ///D: /matlab/index.php.htm

Calculate the price
Make an order in advance and get the best price
Pages (550 words)
$0.00
*Price with a welcome 15% discount applied.
Pro tip: If you want to save more money and pay the lowest price, you need to set a more extended deadline.
We know how difficult it is to be a student these days. That's why our prices are one of the most affordable on the market, and there are no hidden fees.

Instead, we offer bonuses, discounts, and free services to make your experience outstanding.
How it works
Receive a 100% original paper that will pass Turnitin from a top essay writing service
step 1
Upload your instructions
Fill out the order form and provide paper details. You can even attach screenshots or add additional instructions later. If something is not clear or missing, the writer will contact you for clarification.
Pro service tips
How to get the most out of your experience with MyStudyWriters
One writer throughout the entire course
If you like the writer, you can hire them again. Just copy & paste their ID on the order form ("Preferred Writer's ID" field). This way, your vocabulary will be uniform, and the writer will be aware of your needs.
The same paper from different writers
You can order essay or any other work from two different writers to choose the best one or give another version to a friend. This can be done through the add-on "Same paper from another writer."
Copy of sources used by the writer
Our college essay writers work with ScienceDirect and other databases. They can send you articles or materials used in PDF or through screenshots. Just tick the "Copy of sources" field on the order form.
Testimonials
See why 20k+ students have chosen us as their sole writing assistance provider
Check out the latest reviews and opinions submitted by real customers worldwide and make an informed decision.
Nursing
thank you so much
Customer 452749, June 10th, 2021
LEADERSHIP
excellent job
Customer 452773, August 12th, 2023
business
Thank you for your hard work and help.
Customer 452773, February 13th, 2023
Business and administrative studies
Excellent work ,always done early
Customer 452773, February 21st, 2023
FIN571
excellent work
Customer 452773, March 1st, 2024
History
Don't really see any of sources I provided, but elsewise its great, thank you!
Customer 452697, May 8th, 2021
Business Studies
Thank you very much for a good job done and a quick turn around time.
Customer 452615, March 31st, 2021
Human Resources Management (HRM)
excellent job
Customer 452773, June 25th, 2023
Business and administrative studies
Thanks
Customer 452773, March 3rd, 2023
Philosophy
Thank you
Customer 452811, February 17th, 2024
Human Resources Management (HRM)
excellent
Customer 452773, July 11th, 2023
Social Work and Human Services
Although it took 2 revisions I am satisfied but I did receive it late because of that.
Customer 452603, March 25th, 2021
11,595
Customer reviews in total
96%
Current satisfaction rate
3 pages
Average paper length
37%
Customers referred by a friend
OUR GIFT TO YOU
15% OFF your first order
Use a coupon FIRST15 and enjoy expert help with any task at the most affordable price.
Claim my 15% OFF Order in Chat
Close

Sometimes it is hard to do all the work on your own

Let us help you get a good grade on your paper. Get professional help and free up your time for more important courses. Let us handle your;

  • Dissertations and Thesis
  • Essays
  • All Assignments

  • Research papers
  • Terms Papers
  • Online Classes
Live ChatWhatsApp